Laser Cutter Materials
The laser cutter can mark, engrave or cut a large variety of materials. However, some materials simply don't work well (e.g. most metals), and some are extremely dangerous to the machine and to any humans nearby. You must check this list before placing any item in the laser cutter.
It is not always obvious which materials are dangerous. For example, polycarbonate (Lexan) produces flames, lethal chlorine gas, and hydrochloric acid, which will rapidly corrode both the laser cutter internals and the lungs of anyone who breathes in the fumes. Yet acrylic, which looks exactly like polycarbonate, cuts cleanly and safely, and is a very popular lasering material. So check and double-check your materials!
NEVER CUT THESE MATERIALS
These materials will damage or destroy the laser, humans, and potentially the entire shop (fire hazards). Placing any of these materials in the laser will get you perma-banned from the laser!
WARNING: Many plastics are dangerous to cut, so it's important to know exactly what plastic you have. [http://makezine.com/2011/09/22/identifying-unknown-plastics/ Make: has a post describing how to identify unknown plastics.
|Chlorinated plastics (PVC, vinyl, pleather/artificial leather, Sintra, Kydex)||Emits chlorine gas when cut||Destroys the focus lens and mirrors, corrodes metal parts and motion control system.|
|Thick (>1mm) polycarbonate/Lexan||cuts poorly, discolors, catches fire||Polycarbonate absorbs infrared energy, and thus cuts very poorly -- it tends to melt or burn instead. Surfaces near cut edges discolor badly.|
|ABS||Emits cyanide gas, melts, bursts into flame||Tends to melt rather than vaporize, leaving behind gooey deposits on the honeycomb bed. Easily bursts into flame. Also engraves poorly (again, it melts rather than etches).|
|HDPE (milk bottle plastic)||Catches fire and melts||Do we need to say more? Don't use it!|
|Polystyrene foam||Catches fire||This is the #1 cause of laser fires!|
|Polypropylene foam||Catches fire||Just as bad as polystyrene, with the added feature of leaving behind rock-hard deposits.|
|Fiberglass||Emits dangerous fumes||Glass can't be cut, and the resin emits dangerous fumes.|
|Coated carbon fiber||Emits dangerous fumes||The coating emits dangerous fumes. Thin, uncoated carbon fiber mat can be cut, but will fray along the cut edges.|
|Pressure treated wood||Emits dangerous fumes||Should never be burned -- not in your fireplace, and definitely not in our laser.|
|Galvanized metal||Emits dangerous fumes||Zinc fumes are poisonous. Galvanized metal should never be super heated (so don't weld on it either).|
|Mirrored surfaces||Will not cut, reflects laser beam||Mirror surfaces can reflect the laser beam, damaging the cutter's interior components. Some mirrored materials can be placed reflective-side down and cut.|
|Many woods||1/4"||Avoid oily/resinous woods. Some exotic woods can be toxic.||Oily or resinous woods can catch fire|
|Plywood/composite wood||1/4"||Glues in plywood sometimes don't cut well, charring rather than vaporizing. Interior finish grades generally perform better.|| |
|MDF/engineered wood||1/4"||May experience charring when cut.|| |
|Paper, card stock||thin||Cuts well and quickly. Use low power and high speed to prevent burnination. Don't stack multiple sheets, as this increases the chance of fire.|| |
|Cardboard||thicker||Cuts well. Watch carefully, as it may catch fire.||Watch for fire!|
|Cork||1/4"||Quality of the cut depends on the quality of the cork. Engineered cork contains a lot of glue, and may not cut well.||Avoid thicker pieces|
|Acrylic (Lucite, Plexiglas, PMMA)||1/2"||Cuts well, leaves a smooth cut edge. Higher powers may leave smoke/scorch marks along the cut edges.||Stinky fumes|
|Thin polycarbonate sheet||<1mm||Only very thin polycarbonate can be cut. Edges tend to discolor badly. Plycarbonate is a strong IR absorber, and is generally a very poor candidate for laser cutting.||Watch for smoke/fire|
|Delrin||thin||Harder Delrin tends to work better|| |
|Kapton (polyimide)||1/16"||Works well in thin sheets or tape strips|| |