Site Logo

 
It is currently Thu Aug 28, 2014 5:18 pm

All times are UTC - 6 hours




Post new topic Reply to topic  [ 133 posts ]  Go to page 1, 2, 3, 4, 5 ... 14  Next
Author Message
 Post subject: So...what are you working on?
PostPosted: Fri Jan 16, 2009 8:01 am 
Offline
Global Moderator
User avatar

Joined: Mon Jan 12, 2009 10:24 pm
Posts: 634
The initial rush of discussion has slowed down a bit.

I'm looking forward to a meet-up, but until then how about a little bit about what you are working on right now?

I'm a bit scattered in my interests and still recovering from the holiday doldrums, but here goes.

I've been working on learning some simple electronics, as part of that I've been doing a bit of circuit bending and building some simple noise making circuits with and without the Arduino. I finished an optical theramin and my first simple circuit bend and am working on an Atari Punk Console an Arduino based synth and a couple of other things.

I'm a member of local Amateur/Experimental rocketry group for which I am currently tasked with fabricating an impact absorbing nose cone for an 8" rocket that will carry a full beer keg to over a mile high at next years Balls rocket launch.

_________________
Make it happen.


Top
 Profile  
 
 Post subject: Re: So...what are you working on?
PostPosted: Fri Jan 16, 2009 8:37 am 
Offline

Joined: Wed Jan 14, 2009 1:40 pm
Posts: 26
Wait, isn't that risky for the beer?


Top
 Profile  
 
 Post subject: Re: So...what are you working on?
PostPosted: Fri Jan 16, 2009 8:50 am 
Offline

Joined: Wed Jan 14, 2009 1:40 pm
Posts: 26
(Semi-)Active projects:
  • A ~2x3 foot mosaic
  • Getting together some grid-beam for recyclable furniture projects.
  • I also have an Atari Punk Console and some other timer/oscillator-based synthy doodads partially built but I'm not sure what speaker I should be using to test the output so I've kind of put them down for a while. I have a Thing-a-ma-kit waiting for a free weekend.
  • Various software projects.

Projects waiting for spring:
  • A 4x8x12 foot cat cage outside the house allowing cats to move from our basement to their new enclosure.
  • An improved stone wall at the bottom of our new deck steps.


Top
 Profile  
 
 Post subject: Re: So...what are you working on?
PostPosted: Fri Jan 16, 2009 9:40 am 
Offline
Global Moderator
User avatar

Joined: Mon Jan 12, 2009 10:24 pm
Posts: 634
Christopher Weeks wrote:
Wait, isn't that risky for the beer?


It could be. Somebody pulled it off last year though, even though the chute shredded and it came in pretty hot, they immediately tapped it after recovery.

http://www.youtube.com/watch?v=yXZfCXgY ... re=related

_________________
Make it happen.


Top
 Profile  
 
 Post subject: Re: So...what are you working on?
PostPosted: Fri Jan 16, 2009 9:47 am 
Offline
Global Moderator
User avatar

Joined: Mon Jan 12, 2009 10:24 pm
Posts: 634
Christopher Weeks wrote:
(Semi-)Active projects:
  • A ~2x3 foot mosaic
  • I also have an Atari Punk Console and some other timer/oscillator-based synthy doodads partially built but I'm not sure what speaker I should be using to test the output so I've kind of put them down for a while. I have a Thing-a-ma-kit waiting for a free weekend.


I just put a 1/4" jack in my optical theramin so I can plug it into whatever, when I was testing I used a 1/8" jack and headphones. I picked up a small speaker from axeman with intention to use it, but it was much too quiet. I have a satellite from some old AR PC speakers that works perfectly.

Those Thing-a-ma-kits look like fun.

_________________
Make it happen.


Top
 Profile  
 
 Post subject: Re: So...what are you working on?
PostPosted: Fri Jan 16, 2009 11:15 am 
Offline
User avatar

Joined: Wed Jan 14, 2009 10:06 am
Posts: 1219
Location: NE Minneapolis
i assume 8" is the engine size?

at present i'm remodeling my bathroom, which is involving a lot of slate knapping and discovering another glitch to delay things a week. it did give me extra copper bits to build a little steam cannon as a gift, and gave me a lovely excuse to buy a wet saw.

the next project is a skin on frame kayak, and organizing the home brewing supplies into something usable (moved and things are a bit higgilty pigglity)


Top
 Profile  
 
 Post subject: Re: So...what are you working on?
PostPosted: Fri Jan 16, 2009 12:20 pm 
Offline
Site Admin
User avatar

Joined: Sun Jan 11, 2009 6:35 pm
Posts: 861
metis wrote:
it did give me extra copper bits to build a little steam cannon as a gift.

Thanks, just what I asked for santa!


Top
 Profile  
 
 Post subject: Re: So...what are you working on?
PostPosted: Fri Jan 16, 2009 12:28 pm 
Offline
Global Moderator
User avatar

Joined: Mon Jan 12, 2009 10:24 pm
Posts: 634
metis wrote:
i assume 8" is the engine size?


Actually it's the diameter of the keg, we're using the tall skinny type kegs instead of the short heavy ones that they did, it does mean we won't get away with the bounce like they did though.

_________________
Make it happen.


Top
 Profile  
 
 Post subject: Re: So...what are you working on?
PostPosted: Fri Jan 16, 2009 3:27 pm 
Offline

Joined: Wed Jan 14, 2009 1:40 pm
Posts: 26
Oh yeah! I have a bathroom remodel in progress too. And I too bought a wet saw for the project. :)


Top
 Profile  
 
 Post subject: Re: So...what are you working on?
PostPosted: Fri Jan 16, 2009 6:25 pm 
Offline
User avatar

Joined: Wed Jan 14, 2009 10:06 am
Posts: 1219
Location: NE Minneapolis
huh.. cornelius kegs? like for soda? i suppose it might be.... (they're what i've got to eventually set up a home system

i assume the goal is to get back drinkable beer?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 133 posts ]  Go to page 1, 2, 3, 4, 5 ... 14  Next

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL Flash Games